If your Dualshock 4 thumbsticks are starting to show signs of wear and tear, you may need to replace them. This article will discuss the steps involved in the process, including Soldering, Desoldering, and Reassembly. It also describes a few ways to repair your rubber thumbsticks. This article was written with a beginner in mind, but it can also be used by more experienced gamers.
Soldering
You may be wondering how to repair a broken Dualshock 4 thumbstick. First, disassemble the console. You will need a soldering iron. It is best to use a low temperature to begin with, and increase the temperature if necessary. When soldering the thumbsticks, be sure to use the proper technique.
Start by removing the thumbstick covers, which will expose the analog stick modules. Next, unscrew the mainboard from the vibration motors and index triggers. You’ll likely have to resolder the motor wires, but this is a quick and easy process. Be sure to mirror the analog stick positions horizontally after resoldering.
Next, you’ll need a soldering iron and flux core solder. You’ll also need a Philips #000 or Torx T8 screwdriver for PlayStation 4 controllers. A plastic spudger is also useful for this project. After the soldering process is complete, you’ll need to test the controller with a Game Controller Tester (GCT) before putting it together again.
The DualShock controller itself has a battery in it. The battery is connected to two wires: a red and a black ribbon. These two wires connect to a USB board on the DualShock controller. If you want to do this yourself, you should be confident with your knowledge of circuit boards. Otherwise, you may damage the controller permanently.
Desoldering
Desoldering a DualShock 4 thumbstick is not an incredibly difficult process. Luckily, there are a few easy steps you can take to get it back to working like new. First, you must locate the joystick module and orient it to the PCB. Once the module is positioned properly, use a soldering iron to solder the solder to the module’s pins. Once the soldering is completed, the joystick module should be seated flush against the PCB board. If the module isn’t seated flush against the PCB, you can try replacing it.
To do this, you will need to disassemble the controller. Take care not to damage the mainboard, as it is not securely fastened. If you have a plastic pry tool, it may help to loosen the battery tray. Then, gently lift the battery tray from the four retention posts and you’ll expose the mainboard. Desoldering the analog sticks will be a breeze once you’ve got them unsoldered.
The next step is to de-solder the potentiometer. Make sure to remove the solder pad carefully, as forceful removal might cause the lead to come loose. The L3/R3 button is also desoldered in the same way, but it’s permanently integrated into the main housing.
Desoldering a DualShock 4 thumbstick requires a little more skill than other controller modifications. First, you’ll need to use a soldering iron. Then, you’ll need to use flux core solder. Lastly, you’ll need a screwdriver and a plastic spudger.
Once you’ve removed the screws, you should remove the controller from its case and unsolder the thumbstick components. If you find that they’re damaged, you can swap them back to see if they work better. If they don’t, you may have a defective controller, but thankfully, there are several solutions to this problem.
Reassembly
To reassemble your DualShock 4 thumbsticks, you will first need to remove the bottom case. To do this, pry up near the triggers and earphones port and remove the bottom case. The backlight ffc cable and gamepad battery will also need to be removed. Then, line up the two halves so that they are oriented correctly.
If you’ve had the game for a while, you’ll have noticed some problems with the thumbsticks. Fortunately, this can be easily remedied. The Xbox One thumbsticks are a lot firmer and require a bit more torque to move them.
If the thumbsticks are damaged or worn, you can try replacing them yourself. Just remember that the Xbox One thumbsticks are different from those on PS4. To repair your Dualshock 4 controller, you’ll need the controller, a PH000 screwdriver, replacement thumbsticks, and tweezers. Make sure to work on a clean work area and keep the controller out of the way during the repair. The replacement Xbox One thumbsticks should take no more than 30 minutes to replace.
If you don’t have the time or the tools to reassemble your DualShock 4 controller, you can still get replacement thumbsticks for a reasonable price. These thumbsticks can be purchased from a variety of vendors for around $60. As long as you know what you’re doing, you shouldn’t have any issues with your DualShock 4 controller.
Rubber thumbsticks
Often, gamers have problems with their DualShock 4 thumbsticks. Over time, they can tear or deform, and are difficult to use. To remedy the problem, players can buy replacement thumbsticks for their DualShock 4 controller. These replacements are inexpensive, and work exactly like the original.
To install these thumbsticks, simply remove the original controller and install the new ones. The new thumbsticks should fit seamlessly into the controller. Moreover, they’re designed to match the curve of the controller. Once installed, they should look like this. If they are loose, you can use double-sided tape or skid protectors to fix them. If the problem persists, you can replace the entire thumbstick.
Both the DualShock 4 and DualSense controllers have identical button layouts, but the thumbsticks differ in their shape and size. In addition, DualSense thumbsticks have a longer and thicker grip. This makes them more comfortable to hold. They’re also positioned underneath the D-pad, which makes them more ergonomic for users with longer thumbs and bigger hands.
Stick drift is a common problem among DualShock 4 users. When the analog stick drifts, the game character will move around, causing vehicle control issues and camera pans in circles. This issue is often caused by dust collecting around the analogs. This problem was finally rectified with new DualSense controllers, but older versions of the PS5 controllers may still suffer from the problem.
Controller button layouts
If you’ve been playing games with your DualShock 4 for several months, you’ve probably noticed that the rubber on the left thumbstick is wearing away. This is not surprising given that you use the left analogue stick when sprinting in games. In some cases, the wear will be minor and the rubber will simply peel away, while in other cases, the wear will be more severe and the sticks will eventually split.
Whether you’re looking to upgrade your controller, or just want to get a more comfortable grip, there are a few things you should know about the DualShock 4 thumbsticks. Unlike its predecessor, the DualSense thumbsticks have a much thicker and longer body, making them more comfortable to hold. In addition, they are more ergonomic, making them better for people with larger hands or longer thumbs.
